Friday, December 21, 2018

AIR IN BRAKE LINES - Brake fluid absorbs and retains water. The problem arises when the fluid has absorbed as much water as it possibly can -- it becomes saturated. When the brake fluid boils -- especially when there is excessive water in the system -- steam is a by-product. The braking system ultimately compresses this steam and turns it into water. The air separates from the water and before you know it, you have large pockets of air in your brake lines. Your braking system will be fine after you bleed your brakes.

Brake fluid absorbs moisture. That's easy enough to understand, right? But how does moisture in the fluid eventually lead to air in the brake lines? See more brake pictures.
.......................................
Air In Brake Lines

Why is there air in my brake lines?

BY JOSH BRIGGS        





Is your brake pedal feeling a little spongy lately?
Is your brake pedal going to the floor while you sit at a red light or when you're braking at low speeds? If so, chances are you have air in your brake lines.
A hydraulic braking system, like the one found in most cars and trucks, relies on brake fluid for pressure.
The whole system springs into action the moment you step on the brake pedal.
But have you ever wondered why your brake fluid level gradually decreases over time?
The fluid isn't magically disappearing. In fact, there's actually a perfectly practical explanation for this phenomenon.
As your brake pads wear thinner and thinner over several thousand of miles of use, the distance your brake pads need to travel to make contact with your rotors increases.
The hydraulic pistons within the brake calipers slowly extend to keep the brake pads at a uniform distance from the brake rotors as the pads wear.
It's only a very small distance, but if you consider that there are four sets of brake pads -- each set wearing down a little bit more every time you touch the brake pedal -- it's easy to see how the system requires more brake fluid as time passes.
As you probably already know, your brake fluid level decreases as your brake pads wear down. It makes sense, right?
But here's where a somewhat common brake problem begins.
Brake fluid resides in a sealed, air-tight reservoir on top of the master cylinder.
As the brake fluid level drops, air moves in to fill the void.
Wait a minute -- didn't we just say that the system was air-tight?
Well, unfortunately, air does get into the reservoir over time and it eventually makes its way into the rest of the braking system -- including your brake lines.
Every time you open the cap to check your brake fluid level, you're letting air into the system.
When the fluid is at the correct level, air isn't much of a factor; however, the more worn your brake pads are, the larger the void grows.
That's one reason why it is so important to keep the fluid at the proper level.
Water is another factor that can cause brake issues.
Water can actually cause air to accumulate in your brake lines. How so, you ask?
Well, brake fluid is hygroscopic -- it absorbs and retains water.
The problem arises when the fluid has absorbed as much water as it possibly can -- it becomes saturated.
Brake fluid is designed to have an extremely high boiling point; however, if you subject your vehicle to excessive braking, like maybe a trip through the mountains, you can easily cause the brake fluid to heat up to this temperature or beyond.
When the brake fluid boils -- especially when there is excessive water in the system -- steam is a by-product.
The braking system ultimately compresses this steam and turns it into water.
The air separates from the water and before you know it, you have large pockets of air in your brake lines.
A spongy brake pedal is bad news, but there's no need to lose any sleep over it; you probably don't need a complete brake overhaul.
What you do need to do, similar to other brake problems, is address the situation immediately.
Brakes are one of the most crucial safety components on your vehicle.
Obviously, with a shoddy brake system, you're putting your safety and the safety of other drivers at risk.
So, what can you do? It's a safe bet that your braking system will be fine after you bleed your brakes.
This simple procedure will eliminate any unwanted air from the lines and restore your brake pedal pressure.
You can do this at home in your garage or take your vehicle to the local automotive shop to have it done for you.
While you're at it, you should probably change your fluid, too.
Brake fluid, as we mentioned, becomes saturated and can deteriorate over time so go ahead and replace it while you have the opportunity.
With fresh brake pads, all new brake fluid and a properly bled hydraulic system, your brakes should feel firm and as good as new.

 






No comments:

Post a Comment