Showing posts with label Pile foundations. Show all posts
Showing posts with label Pile foundations. Show all posts

Friday, January 3, 2020

PILE FOUNDATIONS - Pile foundations are capable of taking higher loads than spread footings. A pile is basically a long cylinder of a strong material such as concrete that is pushed into the ground to act as a steady support for structures built on top of it. As pile foundations carry a lot of load, they must be designed very carefully. A good engineer will study the soil the piles are placed in to ensure that the soil is not overloaded beyond its bearing capacity. Every pile has a zone of influence on the soil around it. Care must be taken to space the piles far enough apart so that loads are distributed evenly over the entire bulb of soil that carries them, and not concentrated into a few areas. Engineers will usually group a few piles together, and top them with a pile cap. A pile cap is a very thick cap of concrete that extends over a small group of piles, and serves as a base on which a column can be constructed. The load of this column is then distributed to all the piles in the group.


..............................................................................................................................................................
Pile Foundations
understandconstruction.com



A pile is basically a long cylinder of a strong material such as concrete that is pushed into the ground to act as a steady support for structures built on top of it.
Pile foundations are used in the following situations:
When there is a layer of weak soil at the surface. This layer cannot support the weight of the building, so the loads of the building have to bypass this layer and be transferred to the layer of stronger soil or rock that is below the weak layer.
When a building has very heavy, concentrated loads, such as in a high-rise structure, bridge, or water tank.
Pile foundations are capable of taking higher loads than spread footings.
There are two fundamental types of pile foundations (based on structural behaviour), each of which works in its own way.
End Bearing Piles
In end bearing piles, the bottom end of the pile rests on a layer of especially strong soil or rock.
The load of the building is transferred through the pile onto the strong layer. In a sense, this pile acts like a column.
The key principle is that the bottom end rests on the surface which is the intersection of a weak and strong layer.
The load therefore bypasses the weak layer and is safely transferred to the strong layer.
Friction Piles
Friction piles work on a different principle. The pile transfers the load of the building to the soil across the full height of the pile, by friction.
In other words, the entire surface of the pile, which is cylindrical in shape, works to transfer the forces to the soil.
To visualise how this works, imagine you are pushing a solid metal rod of say 4mm diameter into a tub of frozen ice cream.
Once you have pushed it in, it is strong enough to support some load. The greater the embedment depth in the ice cream, the more load it can support.
This is very similar to how a friction pile works. In a friction pile, the amount of load a pile can support is directly proportionate to its length.
WHAT ARE PILES MADE OF?
Piles can be made of wood, concrete, or steel.
In traditional construction, wooden piles were used to support buildings in areas with weak soil.
Wood piles are still used to make jetties. For this one needs trees with exceptionally straight trunks.
The pile length is limited to the length of a single tree, about 20m, since one cannot join together two tree trunks.
The entire city of Venice in Italy is famous for being built on wooden piles over the sea water.
Pile Foundations
Concrete piles are precast, that is, made at ground level, and then driven into the ground by hammering - more on that later.
Steel H-piles can also be driven into the ground. These can take very heavy loads, and save time during construction, as the pile casting process is eliminated.
No protective coating is given to the steel, as during driving, this would be scraped away by the soil. In areas with corrosive soil, concrete piles should be used.
HOW PILES ARE USED
As pile foundations carry a lot of load, they must be designed very carefully.
A good engineer will study the soil the piles are placed in to ensure that the soil is not overloaded beyond its bearing capacity.
Every pile has a zone of influence on the soil around it.
Care must be taken to space the piles far enough apart so that loads are distributed evenly over the entire bulb of soil that carries them, and not concentrated into a few areas.
Engineers will usually group a few piles together, and top them with a pile cap.
A pile cap is a very thick cap of concrete that extends over a small group of piles, and serves as a base on which a column can be constructed. The load of this column is then distributed to all the piles in the group.
HOW PILES ARE CONSTRUCTED
Cast-in-place piles are made in the following steps:
hammer a thin-walled steel tube into the ground
remove all earth left inside the tube
lower a steel reinforcement cage into the tube
cast the pile by pouring wet concrete into the tube
The thin walled steel tube is called the casing, and only serves to form a secure mould for casting concrete that is free from earth and debris. It has no structural role to play after the casting is complete.
Some soils are highly cohesive, meaning that if one drills a hole into the soil that is say 1 foot wide by 50 feet deep, then the soil holds the shape of the hole and does not collapse into the hole and block it.
If such soil is present at the site, then one does not need to leave a casing in place: one can use the casing to drill the hole for the pile, and then remove it, and then cast the pile in place.
This saves costs as the same casing tube can be used to drill holes for all the piles.
Precast Driven Piles are first cast at ground level and then hammered or driven into the ground using a pile driver.
This is a machine that holds the pile perfectly vertical, and then hammers it into the ground blow by blow.
Each blow is struck by lifting a heavy weight and dropping it on the top of the pile - the pile is temporarily covered with a steel cap to prevent it from disintegrating.
The pile driver thus performs two functions - first, it acts as a crane, and lifts the pile from a horizontal position on the ground and rotates it into the correct vertical position, and second, it hammers the pile down into the ground.
Piles should be hammered into the ground till refusal, at which point they cannot be driven any further into the soil.
SPECIAL PILES
Pile driving is very noisy and causes massive vibrations through the soil. For this reason, it is sometimes difficult to use them in sensitive locations.
For example, if an operational hospital or science lab is to be extended, driving piles would cause unwanted disturbance.
Their use is also restricted in residential areas in many countries. The vibrations could also cause structural damage to older buildings that are close by.
In such situations it is possible to use micropiling or helical piling, neither of which rely on hammering.
Micropiles or minipiles are small piles that are constructed in the following way:
Step 1: a hole a little larger than the pile diameter and the full length of the pile is dug into the ground using an apparatus like a soil boring machine.
Step 2: a precast concrete pile is lowered or pushed into the hole.
Step 3: a concrete grout is poured into the gap between the pile and the earth.
Helical piles are steel tubes that have helical (spiral) blades attached to them.
These can be drilled into the ground, meaning that the pile acts as a giant drill bit, and is rotated and pushed into the ground from above, much like a screw drills into wood.
Once the steel pile is driven into the ground, a pile cap is poured on top of the pile to prepare it for the construction above.

This is a site that explains the art and science of building construction in great clarity and detail.  Our goal is to make you understand concepts in building construction.
Written by architects and engineers, the content on the site is actually a result of accumulated years of work experience at building construction sites and design offices.  This expert knowledge of building construction is not available in textbooks!
We also take great pains to ensure that our quality of writing is of a high standard.  We aim to take complicated situations and make them simple and clear, as well as to provide content that is interesting to industry experts and newcomers alike.  Do let us know where we succeed - and where we fail - in this task.
We are a free site - we cover our costs by advertising, so do feel free to click on ads that interest you!

Tuesday, August 6, 2019

FOUNDATIONS AND TYPES - Foundations transfer the load from superstructure to the soil (substructure). Foundations are provided to increase the perimeter so that the load is distributed over a large area. The foundation is the lowest part of the building or the civil structure that is in direct contact with the soil which transfers loads from the structure to the soil safely.

foundation
...........................................................................................................................
Foundations
What Is Foundation And Its Types
Civil Engineering



Foundation is the lowermost structure in any building. It will transfer the load from superstructure to the soil (substructure).
There would have been no need of foundation if the soil is good in shear. The column would have been sufficient.
But column punches (settles or goes inside soil) because of a small perimeter.
So, the foundation is provided just to increase perimeter so that load is distributed over a large area.
In other words, foundation is the lowest part of the building or the civil structure that is in direct contact with the soil which transfers loads from the structure to the soil safely.
Types of Foundation
1.        Shallow Foundations
2.        Deep Foundations
Shallow Foundations
Shallow foundations are those founded near to the finished ground surface; generally, where the founding depth (Df) is less than the width of the footing and less than 3m.
These are not strict rules, but merely guidelines: basically, if surface loading or other surface conditions will affect the bearing capacity of a foundation it is ‘shallow’.
Shallows foundations are used when surface soils are sufficiently strong and stiff to support the imposed loads; they are generally unsuitable in weak or highly compressible soils, such as poorly-compacted fill, peat, recent lacustrine and alluvial deposits, etc.
Shallow Foundation Types:
1.  Pad or column footings (Isolated or Combined)
A - Isolated
used to support single columns. This is one of the most economical types of footings and is used when columns are spaced at relatively long distances
B - Combined
Usually supports two columns, or three columns not in a row. Combined footings are used when two columns are so close that single footings cannot be used or when one column is located at or near a property
2.  Cantilever or strap footings
Consist of two single footings connected with a beam or a strap and support two single columns. This type replaces a combined footing and is more economical.
3. Continuous footings
Support a row of three or more columns. They have limited width and continue under all columns.
4. Wall Footings
Are used to support structural walls that carry loads for other floors or to support nonstructural walls.
5. Mat (Raft) footings (Thickened Slabs)
Consist of one footing usually placed under the entire building area.
They are used, when soil bearing capacity is low, column loads are heavy, single footings cannot be used, piles are not used and differential settlement must be reduced.
Raft foundations are used to spread the load from a structure over a large area, normally the entire area of the structure.
They are used when column loads or other structural loads are close together and individual pad foundations would interact.
A raft foundation normally consists of a concrete slab which extends over the entire loaded area. It may be stiffened by ribs or beams incorporated into the foundation.
Raft foundations have the advantage of reducing differential settlements as the concrete slab resists differential movements between loading positions. 
They are often needed on soft or loose soils with low bearing capacity as they can spread the loads over a larger area.
Deep Foundations
Deep foundations are those founded too deeply below the finished ground surface for their base bearing capacity to be affected by surface conditions. This is usually at depths >3 m below finished ground level.
Deep foundations can be used to transfer the loading to a deeper, more competent strata at depth if unsuitable soils are present near the surface.
Deep foundations are used when there are weak (“bad”) soils near the surface or when loads are very high, such as very large skyscrapers.
Deep foundations derive their support from deeper soils or bedrock
Common Types of Deep Foundations are:
1. Pile foundations
Are relatively long, slender members that transmit foundation loads through soil strata of low bearing capacity to deeper soil or rock strata having a high bearing capacity.
They are used for economic, constructional or soil condition considerations, when it is desirable to transmit loads to strata beyond the practical reach of shallow foundations.
In addition to supporting structures, piles are also used to anchor structures against uplift forces and to assist structures in resisting lateral and overturning forces.
Thick slabs used to tie a group of piles together to support and transmit column loads to the piles.
2. Piers
These are foundations for carrying a heavy structural load which is constructed in situ in a deep excavation.
3. Caissons
Are a form of deep foundation which are constructed above ground level, then sunk to the required level by excavating or dredging material from within the caisson.
4. Compensated foundations
Are deep foundations in which the relief of stress due to excavation is approximately balanced by the applied stress due to the foundation.
The net stress applied is therefore very small. A compensated foundation normally comprises a deep basement.
 foundation




























foundationfoundationfoundation



foundationfoundationfoundation



foundationfoundationfoundation





Foundation