Pages

Wednesday, February 20, 2019

INJECTION MOLDING - Injection molding enables complex shapes to be manufactured, some of which might be near impossible to produce economically by any other means. The wide range of materials enables almost exact matching of the physical properties required by the article, and multi-layer molding enables tailoring of mechanical properties and attractive visual appearance - even in a toothbrush. In volume, it is a low-cost process, arguably with minimal environmental impact. There is little scrap created in this process, and scrap that is produced, and is re-ground and re-used.

Injection molding is a manufacturing technique for making components from thermoplastic material
...............................
Injection Molding
What Is Injection Molding And Why It Is Important
By Todd Johnson

Injection molding is a manufacturing process widely used for producing items from toys and plastic trinkets to automotive body panels, water bottles, and cell phone cases.
A liquid plastic is forced into a mold and cures - it sounds simple, but is a complex process. The liquids used vary from hot glass to a variety of plastics –thermosetting and thermoplastic.
History
The first injection molding machine was patented in 1872, and celluloid was used to produce simple everyday items such as hair combs.
Just after the Second World War, a much-improved injection molding process - 'screw injection' was developed and is the most widely used technique today.
Its inventor, James Watson Hendry, later developed 'blow molding' which is used for example to produce modern plastic bottles.
Types of plastic
The plastics used in injection molding are polymers - chemicals - either thermosetting or thermoplastic.
Thermosetting plastics are set by the application of heat or through a catalytic reaction. Once cured, they cannot be remelted and re-used - the curing process is chemical and irreversible.
Thermoplastics, however, can be heated, melted and re-used.
Thermosetting plastics include epoxy, polyesterand phenolic resins, whilst thermoplastics include nylon and polyethylene.
There are almost twenty thousand plastic compounds available for injection molding, which means that there is a perfect solution for almost any molding requirement.
Glass is not a polymer, and so it does not fit the accepted definition of thermoplastic - though it can be melted and recycled.
The Mold
The making of molds has historically been a highly skilled craft ('die-making').
A mold is usually in two main assemblies clamped together in a press. Making a mold often requires complex design, multiple machine operations and a high degree of skill.
The tool is usually steel or beryllium copper which is used for mold making requires heat treatment to harden it. 
Aluminum is cheaper and easier to machine and may be used for shorter run production.
Nowadays, computer controlled milling and spark erosion ('EDM') techniques have enabled a high degree of the automation of the process of mold manufacturing.
Some molds are designed to produce several related parts - for example, a model airplane kit - and these are known as family molds.
Other mold designs may have several copies ('impressions') of the same article produced in one 'shot' - that is, one injection of plastic into the mold.
How Injection Molding Works
There are three main units which make up an injection molding machine - the feed hopper, the heater barrel, and the ram.
The plastic in the hopper is in granular or powder form, though some materials such as silicone rubber may be a liquid and may not require heating.
Once in hot liquid form, the ram ('screw') forces the liquid into the tightly clamped mold and the liquid sets.
More viscous molten plastics require higher pressures (and higher press loadings) to force the plastic into every crevice and corner. The plastic cools as the metal mold conducts heat away and then the press is cycled to remove the molding.
However, for thermosetting plastics, the mold will be heated to set the plastic.
Advantages of Injection Molding
Injection molding enables complex shapes to be manufactured, some of which might be near impossible to produce economically by any other means.
The wide range of materials enables almost exact matching of the physical properties required by the article, and multi-layer molding enables tailoring of mechanical properties and attractive visual appearance - even in a toothbrush
In volume, it is a low-cost process, arguably with minimal environmental impact. There is little scrap created in this process, and scrap that is produced, and is re-ground and re-used.
Disadvantages of Injection Molding
The investment in tooling - making the mold - typically requires high volume production to recover the investment, though this does depend on the particular article.
Producing the tooling takes development time and some parts do not readily lend themselves to a practical mold design.
The Economics of Injection Molding
A high-quality mold, although of relatively high cost, will be capable of turning out hundreds of thousands of 'impressions'.
The plastic itself is quite inexpensive and despite the energy required to heat the plastic and cycle the press (to remove each impression), the process can be economic for even the most basic items such as bottle caps.
Cheap injection molding has led ultimately to disposability - for example of razors and ballpoint pens.
With several hundred new plastic compounds being developed each year and modern mold-making techniques, injection molding is certain to continue increase in use over the next fifty years.
Although thermosetting plastics cannot be recycled, their use, particularly for high precision components, is also set to grow.

Todd Johnson

·   Regional Sales Manager for Composites One, a distributor of composite materials.
·   B.S. in Business Management from University of Colorado Boulder's Leeds School of Business
·   Business Development Manager for Ebert Composites Corporation

Experience

Todd Johnson is a former writer for ThoughtCo, who wrote about plastics and composite materials for 2-1/2 years between 2010 and 2013. He is a Regional Sales Manager at Composites One, a composite materials distributor in San Diego, CA. Johnson provides support to the Greater San Diego manufacturers of fiber reinforced and polymer products. He regularly attends composite industry trade shows including JEC, ACMA, SME, and SAMPE. In 2008 he presented at the Global Pultrusion Conference in Baltimore, MD. Previously, Todd spent six years as the Business Development Manager for Ebert Composites Corporation. 

Education

B.S., Business, Management, Marketing, and Related Support Services - the University of Colorado-Boulder's Leeds School of Business; attended Griffith University in Queensland, Australia. 
Todd Johnson
ThoughtCo and Dotdash
ThoughtCo is a premier reference site focusing on expert-created education content. We are one of the top-10 information sites in the world as rated by comScore, a leading Internet measurement company. Every month, more than 13 million readers seek answers to their questions on ThoughtCo.
For more than 20 years, Dotdash brands have been helping people find answers, solve problems, and get inspired. We are one of the top-20 largest content publishers on the Internet according to comScore, and reach more than 30% of the U.S. population monthly. Our brands collectively have won more than 20 industry awards in the last year alone, and recently Dotdash was named Publisher of the Year by Digiday, a leading industry publication.

Injection molding is a manufacturing technique for making components from thermoplastic material

No comments:

Post a Comment